HVAC, Plumbing, & Electrical Services in Haslet, TX

I conducted a comprehensive HVAC system tune-up, replacing the air filter and testing drains with 2 gallons of water. I recommended installing a float switch on the primary drain to prevent future water issues. All electrical components were tested and checked. The outdoor coil was washed, and refrigerant levels were verified, with a delta T of 20°. I also suggested a start kit to reduce compressor startup amps, as the current load exceeded the system's maximum rating. The homeowner is considering the repairs but has not made a decision yet.

Upon receiving a call, I promptly responded to address a concern regarding a hose that had been left behind during a previous service. Upon arrival, I located the hose and ensured it was in good condition. I then returned it to the customer, explaining its purpose and usage. The customer expressed their gratitude for the swift and efficient service, highlighting the importance of the hose for their needs. I took the time to confirm that the hose was properly returned and functioning as expected, ensuring the customer's satisfaction with the resolution of the issue.

I conducted a thorough evaluation of the HVAC system. The downstairs unit was operational, but the upstairs condenser was not. Upon inspection, I discovered that the capacitor and start kit were out of tolerance. The homeowner chose to replace the capacitor and install soft starters on both units. After completing the repairs, I verified that the system was functioning correctly. Thank you for choosing our services.

On September 7, 2026, I was contacted by a customer experiencing issues with their HVAC system. Upon inspection, it was determined that the blower motor had failed, preventing the system from functioning properly. The customer opted for immediate resolution and paid upfront for the service. I assured the customer that the part would be ordered from the manufacturer as soon as possible. Once the replacement blower motor arrives, I will install it, ensuring the system operates efficiently. The customer can expect a fully functional HVAC system shortly after the part is delivered.

I conducted a complimentary second opinion on the HVAC system, identifying a failed indoor thermal expansion valve and a reversing valve issue. Following this assessment, I scheduled a comfort advisor to review potential custom system upgrades. The advisor is set to visit today between five and seven, as the system is currently non-operational. This proactive approach ensures the system's functionality is restored efficiently.

Upon arrival, I assessed a minor leak at the kitchen faucet. I carefully disassembled the faucet, identifying a loose cartridge as the issue. After securing the cartridge, I reassembled the faucet and conducted thorough testing to ensure proper functionality. The leak was successfully resolved, and the faucet is now operating correctly.

We successfully completed the task of retrieving the tablet. Upon receiving the request, our team promptly assessed the situation and devised a plan to ensure the tablet was safely collected. We carefully handled the device, taking all necessary precautions to avoid any potential damage. Our team member delivered the tablet to the designated location, ensuring it was securely packaged for transit. Throughout the process, we maintained clear communication with the client, providing updates and addressing any concerns. We are pleased to have successfully completed this task.

I conducted a thorough evaluation of the unit. Upon inspection, it was found that the unit was not reaching the setpoint. I meticulously checked all functions and settings to identify any issues. After a detailed analysis, I determined that the problem was due to a minor calibration error. I corrected this and ensured the unit operates efficiently. Thank you for choosing our expertise.

Today, I inspected two cooling systems. The smaller system showed no superheat (sc) and a subcooling (sh) of 17. This system requires a leak search and additional refrigerant (freon). The larger system had a superheat of 6 and a subcooling of 25, which is due to a dirty filter and a malfunctioning thermal expansion valve (TXV). This system needs a new TXV to correct the issue. Both systems were cleaned and washed. The homeowners have set the upstairs temperature to 83 degrees and the downstairs to 79 degrees, with minimal demand on the systems.

Iciciviv

I conducted a thorough evaluation of the system. The indoor unit is functioning properly, but the outdoor unit was not. I updated the software on the CoolCloud interface, checked the filter, drain, refrigerant, and cap, all of which were in good condition. I discovered the outdoor unit was not receiving high voltage due to a tripped breaker at the main panel. After resetting the breaker, I monitored the system and found no further issues. I also discussed the benefits of the Comfort Club and suggested surge protectors to prevent future problems.

Today, I inspected and serviced three systems. The smallest system required a cut and pull cleaning, drain clearing, and cap replacement. The second-largest system needed cap replacement, drain clearing, and freon refill. The largest system also needed cap replacement and a thorough cut and pull cleaning. Additionally, two smaller units would benefit from new fan motors to prevent high head pressure on the compressors. The largest outdoor unit lacked a cover for the disconnect. I cleaned all three systems, changed two filters, and recommended the homeowner acquire 20×25×4 filters. I also identified significant biogrowth within the systems and suggested UV treatment for all three to maintain good air quality.

We conducted a comprehensive plumbing inspection, identifying several minor issues. Detailed estimates were promptly sent to the customer. During the consultation, the customer expressed interest in relocating their water heater and potentially installing a water softener system. To provide the best possible options and pricing, I coordinated with Plumbing Comfort Advisor Mark W. for a joint visit. On the scheduled day, Mark W. and I arrived to assess the feasibility of moving the water heater from its current location to the garage. We thoroughly discussed the process, potential challenges, and benefits. A detailed estimate was then prepared and sent to the customer via email.

I arrived to address an issue with the upstairs HVAC system not maintaining the desired temperature. The homeowner reported it reached 78° during peak heat, while the thermostat was set at 68°. Upon inspection, the condenser was covered in dirt, and the refrigerant levels were low. Due to the late hour, I scheduled a return visit for the next morning. I returned promptly, cleaned the coil thoroughly, and recharged the system. The temperature differential is now 20°, and the system is cooling effectively. The homeowner opted to leave it running.

During the evaluation, I found that the indoor unit was operational, but the outdoor unit was not. Upon inspection, the outdoor unit was not receiving 240V. The AC breaker at the home panel was tripped and would immediately trip again when attempting to turn it on. The capacitor was in good condition, and a start kit was tried without success. When the compressor was unplugged, the fan started, indicating a failed compressor. I explained the benefits of the Comfort Club, but the homeowner decided to consult a friend who specializes in HVAC before proceeding with any repairs. I left the breaker off at the home panel and the compressor unplugged at the outdoor unit, with the system still down.

Upon arrival, I inspected the system and identified a failed capacitor as the cause of the issue. I replaced the capacitor and performed a minor electrical repair. After the repair, I verified the system's functionality by pouring two gallons of water into the primary drain line, ensuring proper drainage. I also confirmed a 15° temperature split across both systems. Both systems were cooling and fully functional at departure. The capacitor replacement is not covered by warranty. Thank you for choosing Comfort Experts.

Upon arrival, I identified a "transfer wire warning" on a 24kw Generac air-cooled generator. After a thorough inspection, I discovered that the control board was producing only 1.7VDC, significantly below the required voltage. This indicated a fault in the control board. Given that the generator is under warranty, as confirmed by Brian, I proceeded to pause the job to order a replacement control board. The specific part needed is a Generac control board, Model G00721010, Serial 3015378917. Once the part arrives, I will replace the faulty control board to restore the generator's functionality.

Upon arrival, I identified that the combination breaker was frequently tripping, which was traced back to the coffee maker. To resolve this, I removed the combination breaker and installed a regular Homeline 20A breaker, ensuring it was properly secured and tested for functionality. Additionally, I replaced the existing kitchen plug with a Ground Fault Circuit Interrupter (GFCI) for enhanced safety. This change not only prevented the breaker from tripping but also provided an extra layer of protection against electrical faults. The coffee maker was then reconnected, and I verified that both the new breaker and GFCI were operating correctly. The job was completed efficiently, ensuring the safety and reliability of the electrical system.

Upon arrival, I assessed the generator displaying a transfer wire warning code. I removed the panel covers and the transfer switch cover to inspect all connections, ensuring they were correctly placed. Despite these checks, the generator continued to show the same code, a problem it has had since its installation in 2024. I verified the wires and voltage levels but found no issues. During the inspection, I consulted with Brian over the phone while Hunter and I were on-site. We decided to call Mark D, who has more expertise in generator issues, to assist further. Mark D was en route and had previously stopped to address other matters. Don, who originally installed the generator, was not available.

Upon inspection, both the upstairs and downstairs systems exhibited significant issues with clogged primary and secondary drain lines. I began by carefully disassembling the drain underneath the sink, ensuring minimal disruption. The primary and secondary drains were thoroughly cleared of obstructions. Following this, I meticulously removed all accumulated water from the emergency drain pans. To prevent future clogs, I applied specialized pant treatments to both systems. After completing these tasks, I verified that both systems were operational and the drains were fully cleared, ensuring optimal performance.

I was called to address an issue with a kitchen breaker tripping whenever the coffee machine was in use. Upon arrival, I identified the breaker as an arc fault GFCI. I inspected the connections on the kitchen plugs and found them to be loose, so I tightened them. Despite my efforts, I couldn't replicate the tripping issue. However, I recommended removing the AFCI component of the breaker and leaving the GFCI in place to prevent future tripping while still providing essential safety protection. This solution should help ensure the kitchen outlets function properly without unnecessary interruptions.

During the service, I performed a comprehensive tune-up on the 2017 Carrier heat pump. I started by changing the filter and ensuring the Delta was functioning properly. All electrical components were tightened, and the drain was cleared. Although the biological growth was noted, no immediate action was taken. The refrigerant levels were checked and found to be adequate, with the cap within tolerance. The start kit was recommended to lower inrush and extend the compressor's life. A slight play on the condenser motor shaft was identified. The unit was thoroughly washed, and the system was cooling effectively when I left. I also discussed the benefits of the Comfort Club, but the homeowner declined additional services for today. They requested a plumber for 8/3/26 and an electrician for 8/4/26.

On August 1, I evaluated an AC system that was not functioning properly in the morning. After inspecting all electrical components, I found they were in good condition. However, the sub-cooling was below the expected level, indicating a refrigerant issue. Unfortunately, I couldn't add Freon because I didn't have the required R32 refrigerant on hand. I paused the service to return next weekend with the necessary refrigerant. Thank you for choosing our services. We look forward to resolving the issue and ensuring your comfort.

Upon arrival, I assessed a system that was non-operational, with the compressor failing to activate despite the presence of a hard start kit, a fresh capacitor, and a new contactor. After thorough testing and analysis, it was determined that the compressor itself was faulty and required replacement. Additionally, the disconnect needed to be replaced to ensure proper system functionality. I provided a detailed evaluation and recommended the necessary replacements. For a comprehensive price quote, please contact us. Thank you for choosing Comfort Experts. Have a great day.

Upon arrival, I conducted a thorough evaluation of the system to ensure optimal performance. The system was found to be functioning correctly, with no issues detected in the drain, filter, or airflow. Refrigerant levels were confirmed to be within the appropriate range, and the cap was inspected and found to be in good condition. Given the possibility of the unit experiencing thermal stress during the day, I took the proactive step of washing the unit to maintain its efficiency. By the time I left, the system was effectively cooling, ensuring your comfort. Thank you for choosing our services.