HVAC, Plumbing, & Electrical Services in Arlington, TX

I conducted a thorough evaluation of the system, which had been struggling to meet demand. Upon inspection, I discovered a drain line backup that was causing the float switch to trip. I promptly addressed the issue by changing the filter and clearing the drain. Additionally, I cleaned the outdoor unit, which was heavily matted. After completing these repairs, I verified that the system was functioning correctly. The cooling was operational when I finished, ensuring optimal performance. Thank you for choosing our services.

I arrived to replace the old water heater and installed a new Flotec water treatment system. The installation was completed successfully, and I conducted thorough testing to ensure everything was functioning properly. The customer opted for financing through Google, making the process seamless. The new system is now efficiently providing treated water.

Upon arrival, the customer reported that the system was not functioning. Upon inspection, I discovered that the upstairs thermostat was set significantly cooler than the downstairs thermostat. Given that this is a zoned system, the temperature difference was causing the system to become excessively cold, resulting in a 30°F temperature split and triggering a shutdown. I explained to the customer that for optimal operation, the upstairs thermostat should be set approximately 2°F warmer than the downstairs thermostat, as cool air naturally settles while warm air rises. I adjusted the thermostats to 70°F downstairs and 72°F upstairs. After making the adjustment, the system was operating properly with a 20°F temperature split between the supply plenums. Additionally, I noticed that the p-trap for the primary drain line was condensing water onto the ceiling, which needed to be addressed. The customer opted to handle this themselves. Upon departure, the system was cooling as intended. Thank

I conducted a thorough electrical inspection, confirming the absence of issues with the recently installed panel, surge protection, and required safety measures. Grounding was adequate at the water heater and ground rod. The customer raised concerns about a bathroom fan, which was actually a vent issue due to lack of use. I explained the situation and offered replacement options. The house also met all requirements for fire protection and smoke detectors.

Yesterday, I completed a five-hour installation job that was financed through Google financing. The task involved a comprehensive assessment of the existing system, followed by the installation of new components. I began by carefully dismantling the old system, ensuring all parts were safely removed and disposed of. Next, I installed the new components, meticulously following the manufacturer's guidelines to ensure optimal performance. Throughout the process, I maintained clear communication with the customer, providing updates on the progress and addressing any concerns. The job concluded with a thorough inspection to confirm everything was functioning correctly, leaving the customer satisfied with the results.

Credit reject.

Recently, I successfully replaced the capacitor on a condenser unit. The process began with a thorough inspection of the existing capacitor to identify any signs of wear or damage. After confirming the need for replacement, I safely discharged the unit to ensure no electrical hazards. I then carefully removed the old capacitor, taking note of its specifications for the new one. The new capacitor was installed with precision, ensuring all connections were secure and properly insulated. Following installation, I tested the unit to confirm it was functioning correctly and efficiently. The condenser unit is now operating as intended, providing reliable performance.

I performed a comprehensive tune-up on the heat pump system. Key findings included low refrigerant levels, with 45 superheat and 4 subcool, causing the evaporator coil to freeze. I informed the customer and discussed potential solutions. She plans to contact her insurance company for coverage. Additionally, I identified biological growth in the plenum and blower, recommending a UV system. High dust levels in the ducts were noted, suggesting duct cleaning. Lastly, the compressor showed high amp start-up, for which a soft start was recommended to reduce amps by 70%.

During the service, I performed a comprehensive tune-up of the system. The filter was changed, ensuring optimal air quality. The drain was checked and found to be clear, preventing any potential water accumulation issues. The system's Delta was assessed and found to be within acceptable limits. All furnace components were inspected and deemed acceptable. The refrigerant levels were verified to be adequate, and the electrical components were tested and found to be within tolerance. Additionally, I recommended upgrading to a soft starter to enhance system efficiency. I also suggested installing a drain switch on the primary unit instead of using an emergency pan. Lastly, I ordered new Air Ranger filters (20x25x1) for future use, as there was no need to replace the current filter at this time.

Upon arrival, I assessed the issue with the air conditioning unit, which was experiencing a drain backup. The customer reported that water was not draining properly, causing a backup. I began by inspecting the drain line under the unit to identify the source of the blockage. Using a small hand auger, I carefully navigated through the drain to dislodge the obstruction. After several attempts, the blockage was successfully cleared, allowing the water to flow freely. I then tested the unit to ensure that the drain was functioning correctly and that the AC was operating efficiently. The customer confirmed that the issue was resolved, and the system was back to working properly.

Both HVAC systems were in severely clogged and damaged conditions. The motor wheels required thorough cleaning, and one motor needed replacement along with its heat kit and breakers. Additionally, the second system needed a cut-and-pull cleaning to address issues with the evaporator coil. The ducts in the house required a level 2 cleaning for both systems to ensure optimal performance. We also discussed the possibility of system replacement to address these extensive issues.

I performed a comprehensive tune-up, ensuring the system operates efficiently. The Delta pressure is optimal. The HVAC drain is clear, but a house plumbing backup was identified, prompting a plumber's visit. I replaced the air filter and checked for software updates. All furnace components are functional, though I cleaned the flame sensor to prevent future issues. The outdoor unit is in excellent condition. I also discussed the benefits of the Comfort Club and completed the flame sensor cleaning. The system is cooling effectively. Thank you for choosing our services.

I addressed all red tag items, ensuring compliance with safety standards. The water heater was inspected and repaired, with any necessary adjustments made to meet regulatory requirements. I conducted a thorough check of the unit's functionality, safety features, and overall condition. The water heater is now fully operational and ready for a final inspection.

During the service, I performed a comprehensive tune-up on the system. The Delta pressure was found to be within optimal range, and I changed the filter to ensure clean air circulation. The drain was clear, preventing any water accumulation issues. However, the UV bulb had failed, which I identified as a critical issue to address to prevent biogrowth. I recommended either replacing or upgrading the UV bulb. The heat strip amp draw was satisfactory, and refrigerant levels were balanced. All electric components were within tolerance. The attic insulation was at 8-9 inches, and I suggested increasing it to 14 inches to improve efficiency and reduce energy costs. I also washed the outdoor unit and recommended installing a surge protector for added protection. Lastly, I updated the membership to the Comfort Club. No additional work was accepted for the day.

I conducted a comprehensive super tuneup, meticulously examining the entire system. I cleaned all components thoroughly, ensuring no dirt or debris remained. The air filter was replaced to enhance system efficiency. I also inspected and cleared the drain lines to prevent any blockages. After completing these tasks, I performed a test run to confirm that every part of the system was functioning correctly. The system performed flawlessly, ensuring optimal performance. Thank you for choosing our services.

Upon arriving, I conducted a thorough inspection and identified that the high pressure switch and hard start were not functioning correctly. After discussing the issue with the homeowner, I decided to bypass the high pressure switch to ensure the system could operate safely. Next, I installed the hard start kit, which is designed to assist the compressor during startup, thereby improving overall efficiency. Following the installation, I meticulously tested the system to confirm that everything was working as intended. The system was successfully restored to full functionality, and I took the time to clean and organize the area, leaving it in excellent condition. Thank you for choosing our services.

I successfully installed a new warranty evaporator coil unit today. The installation process began with a thorough inspection of the existing system to ensure compatibility. I then carefully removed the old unit and installed the new one, making sure all connections were secure and efficient. After the installation, I conducted a series of tests to confirm that the new unit was functioning properly. The customer was pleased with the results, and I collected payment via credit card. Additionally, the customer will enjoy a 6-month free membership as part of their purchase, enhancing their overall satisfaction with the service provided.

Upon arriving, I began by inspecting the air conditioning system to identify the issue. The evaporator coil was found to be faulty, so I proceeded to replace it. After installing the new coil, I pulled a vacuum on the system to ensure all air was removed, achieving a vacuum level of 217. This step is crucial for maintaining system efficiency and preventing future issues. Following the vacuum pull, I recharged the refrigerant, carefully adding the correct amount to achieve a 20-degree temperature differential. The system was then tested, and it was confirmed to be cooling effectively. The job was completed successfully, ensuring the system operates efficiently and reliably. Thank you for choosing our services.

I conducted the first Seasonal Tune-Up (STU) on the HVAC system. The inspection included a comprehensive tune-up, testing both the AC and heater, which operated correctly. The air filter required replacement, but no filter was provided at the time. All electrical components were tested and found to be functioning properly, including the heater and safety mechanisms. The outdoor coil was cleaned, and refrigerant levels were checked, with a Delta T of 18° recorded. The drain lines were inspected, revealing a partial clog in the primary drain line, causing slow drainage and partial buildup. Although the homeowner was not present, I discussed the issue with their daughter and informed the homeowner over the phone. They acknowledged the problem and agreed to clear the drain lines themselves. Additionally, I recommended duct cleaning to remove accumulated dust and debris. No further work was performed today, and the system was left operational and cooling upon my departure.

Today, I performed a thorough drain clearing on the system, which had accumulated a significant amount of slime buildup. I began by inspecting the drain lines and identifying the areas with the most substantial blockage. Using specialized tools, I carefully removed the slime and debris, ensuring that the drain lines were completely clear. I then flushed the system with clean water to remove any remaining particles and checked for proper drainage. After confirming that the system was functioning optimally, I reassembled all components and conducted a final inspection. The system is now fully operational and ready for cooling.

During the service, I meticulously cleaned the condenser unit and discovered two filters instead of the required one. I left the extra filter inside for future reference. The refrigerant levels were optimal, and the system's superheat was within the acceptable range. I recommended a soft start to minimize high amp draws and prevent compressor failure. Additionally, I identified that the UV light system was non-functional and suggested a replacement to prevent bio growth. Thank you for choosing our services.

Upon inspection, I identified a leak under the sink, a slow drainage issue in two sinks, and a broken plastic nut on the p trap under the kitchen sink. The customer, who frequently handles repairs himself, opted to address these issues independently. I flushed the water heater and tested the temperature and pressure relief valve, confirming that both were functioning correctly. Additionally, I noted that one sink and the shower were non-operational, but the customer chose not to have these fixed. The work was completed efficiently, ensuring all identified issues were thoroughly documented.

Upon inspection, the system's filter was heavily clogged, causing the compressor to ingest liquid and freeze the entire system. I replaced the filter to restore proper airflow. Additionally, I installed a new soft start device to prevent sudden compressor surges and a compressor cap 45/5 to enhance efficiency. The system is now fully operational and ready for use.

Upon arrival, I assessed the situation where the customer's disposer had malfunctioned, resulting in a sudden loss of water that caused significant structural damage. I began by thoroughly inspecting the affected area to understand the extent of the damage. I then coordinated with the customer to ensure they would obtain a replacement disposer. Once the new disposer was ready, I promptly returned to the site. I carefully removed the faulty disposer and installed the new one, ensuring all connections were secure and functioning correctly. Throughout the process, I maintained clear communication with the customer, providing updates and ensuring their satisfaction with the repair. The job was completed efficiently, restoring the functionality and integrity of the area.

I successfully installed an Amana 2-speed 36k upflow heat pump, ensuring optimal performance for efficient heating and cooling. The system features high-efficiency filtration, which enhances indoor air quality by capturing dust, pollen, and other allergens. Additionally, I integrated a UV system with oxidation technology to further purify the air, eliminating bacteria and viruses. The installation also included a code kit, ensuring compliance with all relevant regulations and standards. This comprehensive setup guarantees a healthier living environment and improved energy efficiency.