Perrin TX

Came to house for half of house not working and quoted to fix it

Upon technicians arrival, tech talk to homeowner technician started inside where float switch was upside down and going off technician checked the drain drain was clear and was not clogged technician cleared wet, switch and van came on technician found W was not connected on the thermostat. Technician then connect to W on thermostat and the unit kicked on immediately working properly

Repaired water line at broken burried frost free hydrant. In cow field.

Upon arrival tech was shown to the condenser and furnace tech started at the furnace. It was blowing hot air. Tech went to the condenser. Tech turned off the condenser and turned it back on. When to condenser started back up the h heard clicking coming from the reversing valve tech checked the reversing able and found it was good when tech put the wire back on tech found that the wiring was lose that wasn’t allowing it to work properly. When tech put everything back together tech had checked inside the sc and sh where good and the vents where blowing 56 degrees. Customer wants to call the office and talk about the estimate and service fee and price of fix. Tech talked to supervisor to see if unit was under p&l the only thing that is owed is the service fee of 79.20. Tech had to leave to get service to make phone call to supervisor. Once tech got back to talk to owner the gate code wasn’t working.

Upon arrival, tech met up with homeowner and discussed about everything that tech would be looking for. Tech got in the attic and looked at return and supply Plenum. Tech went inside the house and looked at all the supply and return vents. Tech suggested level two duck cleaning due to hide dust.

Repaired 1" pvc line in field to horse bin Repaired 1/1/4 pvc line to horse bin near home

Tech Cody arrived to customer's home and met the homeowner. When I arrived the unit was cooling, the customer wanted an estimate for replacing the condenser casing after a tree branch fell on it. While I was inspecting the unit, the compressor went into thermal overload. I cooled it off and the system turned back, I did testing to find what caused the compressor to go into thermal overload but was unable to find a definitive cause. I did notice that the system has a TXV but no hard start kit installed which could be a contributing factor. System operated with no issue for 40 minutes after turning back on and was cooling the home. Estimate for replacing the condenser fan casing: $1000

Install 9k heat pump mini split for shed and adding 3 plugs to shed

7/11/24 Installed 40A feeder underground to 6 circuit sub panel in shed. Installed 3 new outlets in shed. Installed switch and keyless fixture for general lighting. ADD $600 FOR NEW SWITCH AND LIGHT. Installed 240v 20A home run to exterior disconnect for mini split.

Upon arrival condenser fan was on the thermostats was turn off. Tech moved wires and the condenser fan started working properly.

Upon techs arrival tech was shown to the Kennel. Tech had opened up the condenser panel and it started to poor rain for a hour and continued to do so once tech got back to the truck it was stuck once we got the truck unstuck the rain had quit. When tech unplugged the disconnect the condenser was still getting power. Tech noticed that the disconnect had arc marks and suggested to replace that. The contacter was bad due to ants. Tech replace the disconnect and contacter once both where replace the unit was running up to standards.

Tyler L. completed annual electrical system inspection.

There are quite a few things that need to be done on the house one of my recommendations was moving the panel outside for a panel change due to the location the age and the overall condition of the panel but beyond that the weather head and the meter base are tilted off of the wall the ground rod over by the outside unit isn't even attached to wires they did have a few outlets that had an open ground and they were having trouble with two fan lights upstairs but one wasn't showing the problem and the other one we could not get to turn on because the remote

Customer is interested in replacing the system under the USDA grant. Comfort advisor scheduled to speak with the customer tomorrow between 3-5pm. Straight cool condenser with air handler installed in 2005. System is low on R-22 refrigerant. Evaporator coil is dirty. Blower wheel is dirty. No drain protection installed. No emergency drain pan installed. Compressor and condenser fan motor are acceptable. Suggest replacing system due to age and reliability of current equipment.

Alex D 3/22/24 - Installed 4 2x6 vertical supports underneath platform as well as a 2x6 horizontally underneath the center of the platform secured everything with wood screws fixing sagging platform and leveling out the furnace also tested drain line. with customers permission cut out part of the door trim to ensure customer could easily change the filter

Ian C. completed annual plumbing inspection.

Cust has 14yr water heater leaking around the bottom Lots of corrosion and rust Showed cust and cust wants to wait to replace at this time

During initial start up of the system could hear water near the heat exchanger that had built up after releasing the negative pressure built up in the drain line water started pouring down the drain line and system stayed running the whole time and cycled on and off properly Let customer know what could have caused the problem and it should be fine from here on Left customers house with system operating properly

Upon arrival system was having a hard time staying on. Heard water in flue drain. Opened and cleared all drain tubes, washed drain box till no more debris came out.

System operational. Condensate line had a heavy droop which was backing up water, adjusted appropriately. Pressure switch tubing to inducer was heavily kinked, fixed. Monitored system, pushing 118 degrees. System shutoff sheet reached set point in tstat and cache back on with a call.

I have sent via email and updated estimate due to the change in the scope of work and I would like to set up a phone call for the latest to be Monday to talk about any kind of decisions that have been made

Need to call him on Saturday the 9th and ask about his position on the the work

System still wasn't cooling as should added 3lbs14oz of 410a together correct superheatsystem is cooling as should

Upon arrival system was not cooling. Found last tech left gauge piece on gauge hookup and had become loose releasing Refrigerant. Added 1lb 14oz of 410a to system to get recommended subcool at 10 subcool reading 11 Recall on previous technician