AC Repair & Installation In Millsap, TX

No service fee we had just done a panel change and the problem could be the breaker I switched out the breaker and adjusted a two to three prong adapter but I'm going to talk to Brian to get some estimates on changing out some of these 2 prongs

Super tune up performed today on a Coleman downflow air handler with heat pump installed in 2016. All electrical connections are tight with no corrosion. PSC blower motor and capacitor are acceptable. Blower wheel and evaporator coil are clean. Evaporator coil has some corrosion present. Compressor and condenser fan motor are acceptable. Refrigerant levels are in range. Reversing valve and defrost control board are working properly. Outdoor unit was washed and waxed. Highly suggest adding a compressor saver to the outdoor unit to help with the reliability of the system upon start up.

Install 42k heat pump outdoor unit with new slab

Quoted 2 systems, moving both closet units to attic with new ductwork for $57,894

2019 indoor unit. 2010 3.5t hp condenser. Condenser unit is unlevel and service lines are buried under dirt. Compressor inrush amps exceed manufacturers LRA specifications. Heavy wobble on condenser fan motor. Bearings failing on condenser fan motor. Thermostat physically won go below 69° Dirty ductwork can be seen outside the supply vents. Due to the age and state of condenser unit and the end of life data fro. The compressor behavior, homeowner agreed to speak to a CA 11/15/24 @10am Son will most likely be present to help since homeowner is hard of hearing. A new condenser unit with a pad, duct cleaning and surge protection.

Install 48k electric downflow with standard filtration and code kit

.

Changed air filter

Amana heat pump with air handler installed in 2018. All electrical connections are tight with no corrosion. Heat strips are pulling proper amperage. Ecm blower motor is acceptable. Blower wheel and evaporator coil are clean. UV bulb is on and working. Aprilaire 213 filter is dirty and needs to be changed. Customer did not have a new filter. Compressor and condenser fan motor are acceptable. Refrigerant levels are in range. Reversing valve and defrost control board are working properly. System is running in cool upon departure.

Upon arrival, tech was shown to furnace thermostat and condenser. Technician started with the furnace. Everything looked to be up to technician standards tech notice wet switch was at bottom of the floor, where it is supposed to be so they do have drain protection. Technician headed to condenser technician found fan motor wasn’t running up to specs. Technician got ratings on fan motor and they were not meeting standards technician then moved to compressor where the readings were up to technician standards.

10/22/24 Found fuses on bus bar melted, swapped spare fuse around and was able to get system operational, getting with Mark on refrigerant and operation looks like txv has failed again

Set solar lead for the 22nd Rob has been given the info

2004 indoor 2008 outdoor straight electric. I informed homeowner that the heatstrips are non functional and offered to diagnose, homeowner politely declined saying Brian H was going to install a new system soon. (Brian H favorite aunt).

Main drain line repair Returning tomorrow to complete

Installed customer supplied thermostat. Performed function check. System running normally at time of departure.

Upon arrival tech noticed that the thermostats was set at 74 and it was 64 degrees in the house. Tech went to the air handler and poured 2 gallons down the trap and found the drain was clogged tech unclogged the drain and poured 4 gallons down the drain to check to make sure tech had cleared it completely

Upon arrival tech was shown to the air handler and condenser tech started with the airhandler. The air handler was working properly. Tech moved to the condenser and found that is was working properly. Tech looked at the filter the filter was dirty once tech changed the filter the spilt was at 15. Upon arrival the unit was pushing 56 degree out of the unit

Goodman package unit heat pump installed last year. All electrical connections are tight with no corrosion. Ecm blower motor is acceptable. Blower wheel and evaporator coil are clean. Heat strips are pulling proper amperage. Reversing valve and defrost control board are working as they should. Compressor and condenser fan motor are acceptable. Refrigerant levels are in range. Unit was washed and waxed. A compressor saver was added on this visit to help with the efficiency and reliability of the system.

Broken toilet flange in hall bath mark w to return for fix Repair toilet in master, installed 2 angle stops at toilets one in master one in hall bath

10/8/24 Replaced yard line and home pipe and shut offs Returning tomorrow to complete rec work

2012 Goodman package Checked and tightened all electrical connections Customer recently changed filters Drain was clear and draining Blower motor and wheel have build up on fins Evaporator coil was acceptable Ignition system is functional All safeties are functional at this time Recommended Blower cleaning

.Replaced a fixture for customer. Sold estimate for 200 A upgrade. PLEASE SCHEUDLE WORK FOR 10/16 ALL DAY. MARK W WILL BE JOINING ME FOR THE DAY. PLEASE ADD HIM IN. Brian H is aware of contacting tri county. Will need to follow up on that the Wed or Thursday prior. 10/9- 10/10. To insure disconnect is scheduled for 10/16. Customer paid half down $5574.50.

Replaced yard line and home pipe and shut offs Gave estimate for replacement of water supply lines, need to return to complete rec work

X-13 blower motor was replaced on the upstairs unit. Wet switch installed on the downstairs air handler and compressor savers installed. Performed function check on both systems. Both systems are working properly upon departure. Refrigerant levels are acceptable on both systems and all amp draws are in range.