AC Repair & Installation In Rhome, TX

Arrived onsite and removed the hose bibb at the end of home per the customers request. Tested after repairs were made everything working properly.

Arrived to address a persistent leak under the kitchen sink caused by a worn-out pipe joint. After carefully inspecting the area, I discovered the seal had deteriorated and replaced it with a durable, high-quality fitting. Once the repair was complete, the leak was resolved and water was flowing smoothly again.

2018 Amana airhandler Checked and tightened all tightened all electrical connections Changed Customer provided filter Drain had some build up in trap Heat strips were functional and within manufacture range Blower motor and wheel were acceptable Evaporator coil was acceptable Condensate pan has biological growth build up Uv system is no longer functional 2018 Amana Heatpump Checked and tightened all electrical connections Dual run capacitor was within manufacture range Primary electrical unit was acceptable Refrigerant levels were acceptable at this time Fan and motor were acceptable Condenser coil was acceptable Washed Condenser coil from inside out Cleared debris out of unit Waxed top of unit Recommended anti microbial pan treatment for drain as well as uv upgrade and compressor saver

Inspected hose bibb she said she was having issues with. That valve is working properly. Went ahead and rebuilt a toilet I hall bathroom by front door. Tested after repairs were made everything working properly.

2023 intertherm airhandler Checked and tightened all electrical connections Customer recently changed filters Heatstrips were functional and within manufacture range Drain was clear and draining Blower motor and wheel were acceptable Evaporator coil was acceptable Airhandler door has slight air leak Recommended weather strip to prevent unfiltered air into system 2023 ducane straight electric Checked and tightened all electrical connections Dual run capacitor was within manufacture range Primary electrical unit was acceptable Refrigerant levels were acceptable at this time Fan blades and motor were acceptable Condenser coil was acceptable Washed Condenser coil from inside out Cleared debris out of unit Waxed top of unit Recommended pan treatment for drain and compressor saver

11/21/24 Problem going into heat pump mode. Have fixed temporarily but would like to return Monday morning to further evaluate the issue. Please set up a return visit for Monday first call.

Upon arrival, technician was shown to air handler condenser and thermostat. Technician started at the condenser where tech washed and waxed unit after technician got inrush of 132 which is above data tags limit. It has gone up over the year. Tech looked at previous pictures. Tech is recommending a compressor saver, which will lower it by 40%. Technician checked fan motor as well as compressor both were looking OK and up to technician standards. Technician headed up to attic tech pulled filter out. It was a little dirty technician didn’t see another filter to replace it with. Everything inside the air handler looked clean and up to technicians standards. Technician talk to homeowner about a compressor saver and explain the purpose of it. Husband wasn’t home. Technician will send a invoice of the compressor saver and let them decide.

Tech Cody arrived to customer's home and met the homeowner. When I arrived the thermostat was callingmfor cool but the system would not kick on. The outdoor control board was giving me the 04 error code for locked rotor, I diagnosed a failed capacitor which was causing the code to show. I shared my findings with the homeowner and replaced the part under warranty P&L. Once replaced I turned power back on to the unit and the system began to cool. The compressor and fan motor were operating within manufacturer range and the refrigerant charge was at acceptable levels at this time. I also replaced the filter while I was there and saw that the indoor coil and blower were clean and the UV light was functioning properly. System was cooling when i left.

2012 Goodman airhandler Checked and tightened all electrical connections Customer changed recently changed filters Drain was clear and draining Blower motor and wheel were acceptable blower wires have biological growth build up Evaporator coil was acceptable 2012 Goodman Heatpump Checked and tightened all electrical connections Dual run capacitor was out of manufacture range Primary electrical unit was acceptable Refrigerant levels were acceptable at this time Fan blades and motor were acceptable Condenser coil was acceptable Washed Condenser coil from inside out Cleared debris out of unit Waxed top of unit Recommended uv system for biological growth, replacement of Dual run capacitor and compressor saver

9/10/24 Arrived onsite customer said her child has Covid needs to reschedule for a different day.

No quote

Etu. Recommended whole home surge protection. Recommended repairing service entrance conduit into meter socket to prevent future problems. Emailed estimate and spoke to customer about upgrading membership. Customer would like an email regarding home budget protection plan.

Arrived for service Eval Downstairs compressor cap failed Temp replacement to check system Low refrigerant Comfort Advisor tomorrow 3pm to replace system

Install c/s sink keeping original faucet with new pop up assembly supplied by CE. Install 1 other pop up assembly on other lavatory sink in same bath With wh flush under plumbing inspection 31

Install c/s sink keeping original faucet with new pop up assembly supplied by CE. Install 1 other pop up assembly on other lavatory sink in same bath *Need to put on schedule for Tuesday morning July 2nd *

For the super turn up we inspected the air handler and condenser, all equipment was measuring within manufacturer specs besides the compressor capacitor. This capacitor was well under the 5% tolerance. Additionally inform the customer is filter was dirty and that would need to be replaced sooner rather than later.

06/08/24 TS- quoted for drain cleaning bathroom sink and tub. Also quote for replacing P-Trap under sink with new 1.25"

Quote

During inspection I found a primary electrical is comprised, also found flex duct not attached any more Gave cust estimate will return asap to complete rec work

Amana heat pump with air handler installed in 2020. All electrical connections are tight with no corrosion. Ecm blower motor is acceptable. Blower wheel and evaporator coil are clean. Delta T at 19 degrees. Compressor and condenser fan motor are acceptable. Compressor saver has been installed. UV bulb was replaced on this visit. Refrigerant levels are in range.

45 capacitor Saftey float Compressor saver Uv light System is fully functional.

Tech arrived at a service call. Upon inspection the main breaker was tripping. The compressor was disconnected and the fan ran. The compressor was tested and failed the Ohms test and resistance test. The capacitors were out of tolerance. The wire insulation was damaged on the fan motor and was touching bare metal. The contactor was scorched. The indoor system was not accessible today. The customer was informed of recommendations today. Due to age, condition, price of repairs and presence of R22; it is recommended that the customer speak with a Project Manager about upgrading to something more reliable with warranties behind it. The customer will speak with his wife and call in about financing options tomorrow. The tech will follow up at a later time of we haven't heard from them by then. Email is nmkane4676@gmail.com