AC Repair & Installation In Boyd, TX

4 year old Amana air handler and heat pump. All electrical connections are tight with no corrosion. Heat strips are pulling proper amperage. Ecm blower motor is acceptable. Blower wheel and evaporator coil are clean. Compressor and condenser fan motor are acceptable. Compressor saver has been installed. Refrigerant levels are in range. Reversing valve and defrost control board are working properly. Outdoor unit was washed and waxed.

Upon arrival Customer stated system would not cool and outdoor heatpump would not run. During evaluation found that the heatpump had 04 code (locked rotor), tested dual run cap and cap tested withing range. Reset system and checked Refrigerant through line and ambient air temp within range. Heat pump does not have hard start kit system needs hard start kit to prevent 04 codes again. Customer agreed to install compressor saver

Replaced the shower valve cartridge for the moen shower valve located in master bathroom,

Sent estimate for manual transfer switch and generator plug jnstall.

Arrived to no cool. 4 year old Amana heat pump with air handler. Outdoor unit had L6 code meaning a failed start capacitor. Replaced 40mfd capacitor and 3 ton compressor saver that had also failed. Performed function check. System running and cooling the home upon departure.

Emailed estimate to remove 3 can lights. Mount boxes and hang 3 fixtures.

Upon arrival indoor was blowing warm air and Condenser was not running. After evaluation found Dual run cap failed and Condenser coils were dirty. Replaced 45/5 dual run cap and cleaned coils

Tech Cody arrived to customer's home and met the homeowners. 4 year old amana hest pump. When I arrived the outdoor unit was not running. When I opened up the unit the control board was not giving any error codes. The system was receiving 24V from the thermostat but was not turning on and the control board said the system had 240v. I verified high voltage and then turned off high voltage to the outdoor unit. I then turned it back on and the system went through it's short cycle timer and turned on with no issue. I repeated this test another 5 times and every single time the system operated normally and began to cool. The auxiliary motor starter was within tolerance, the compressor and fan motor were operating within manufacturer range. I let the system run for 10 mins and checked the refrigerant charge, my readings showed that the system was properly charged. Inside the filter was clean, the coil was clean, the blower was clean, and the system had a 21 degree temperature split, coming o

Tech Cody arrived to customer's home and met the homeowner. When I arrived the system was on but not cooling, the customer mentioned he had noticed issues with the cooling 2 months ago. I found both indoor and outdoor coils to be heavily caked in dirt and dust needing a major cleaning. I explained this to the customer and gave him and estimate for cleaning the coils. He decided he would clean them himself and call us back out if the system wasn't cooling even after the cleaning.

AC service call

AC tune up. Arrived at the home to inspected their air conditioning system to ensure it was working properly for the summer. The filter was changed but there were no major issues found with the system.

Arrived for service call Compressor all draw so high is tripping the breaker and likely to fail outright soon Other system soon to follow Comfort Advisor set for tomorrow at 12

Upon arrival system was on and operating, found that the compressor saver was compromised. Replaced under warranty. Running amps 8.3 Refrigerant acceptable superheat 10 subcool 7.3 IAT 71 Upon further inspection I found that the air handler control board was casting for an update. Updated board, reset system. Confirmed system start up was acceptable, Amp draws acceptable, Refrigerant levels acceptable. System is on and operating efficiently Requested that cust does not flip breaker to outdoor system if this happens again. If no more issues occur after one week I recommend scheduling a follow up visit to run system diagnostic test when temp outdoor is 95+ preferably around 1

System was on and working upon arrival Cust said breaker on disconnect kept tripping Found loose wire on breaker and a loose ground connection Replaced breaker with proper sized breaker and tightened connections System is on refrigerant acceptable Amp draws acceptable, no codes on boards

Arrived to water leaking from the emergency drain pan and through the ceiling. Primary drain was blocked at the drain pan. Cleared blockage and poured vinegar through the drain. Added a drain treatment strip to keep the drains clear. Vacuumed the water from the emergency drain pan. CWF Restoration is meeting with customer tomorrow morning about the water damage to the ceiling.

Upon arrival I found Cust condensation drain pan was not level causing water to build up in airhandler. Lots of biological growth in airhandler Primary drain was clogged Cleaned biological growth and cleared drain Installed uv germicidal light System is on and operating efficiently Refrigerant levels acceptable Poured 5 gallons of water through drain pan to see confirm properly draining

2011 Goodman airhandler Checked and tightened all electrical connections Changed Customer provided filter Drain was clear and draining Blower motor and wheel were acceptable Evaporator coil has some build up of dust and dirt Condensate pan has some growth 2011 Goodman Heatpump Checked and tightened all electrical connections Dual run capacitor was within manufacture range Primary electrical unit was acceptable Refrigerant levels were acceptable at this time Fan blades and motor were acceptable Condenser coil was acceptable Washed Condenser coil from inside out Cleared debris out of unit Waxed top of unit Recommended uv bulb replacement, compressor saver and pan strip

05/13/24 TS- no issues, waterheater is 9 years old but in good condition. All inside fixtures are in good condition

Propane furnace with straight cool condenser installed in 2019. All electrical connections are tight with no corrosion. Refrigerant levels are in range. Blower motor, compressor and condenser fan motor are acceptable. Customer complained of poor air flow in back bathroom. We installed the ductwork. I cut down a support in the duct in order to straighten the path of the air and air flow improved slightly.

Completed hvac maintenance.

Blower wheel is dirty Coils are dirty Ducts are dirty System is operating efficiently Refrigerant levels acceptable Recommended to cust lvl 2 duct cleaning or blower wheel clean and coil clean Need to follow up, system is operating efficiently at this time. Need to clean indoor system

Evaporator coil and line set were freezing, leak tested both indoor and out door. Couldn't find leak, system also have heavy amounts of biological growth that customer is concerned with. Customer stated she doesn't want it in her home anymore, causing heavy allergies. Setup appointment for CA for 3/19/24 10-2.

No service fee because this is the same problem I've been addressing if it's not fixed this time I will be getting into contact with their service provider