HVAC, Plumbing, & Electrical Services in Azle, TX

Ant to bring electrical anode rod with me when I come to do work To replace shower valve will have to cut hole in closet on back side of the shower. Can not fix the hole that we cut to get access to shower valve

2015 Carrier Gas Furnace Checked and tightened all electrical connections Changed customer provided filter Drain was clear and draining at this time UV system is functional Blower Motor and wheel were acceptable Blower cap was within manufacture range Evaporator coil was acceptable 2015 Carrier Straight Cool Checked and tightened all electrical connections Dual run cap was within manufacture range Primary electrical unit was acceptable Refrigerant levels were acceptable at this time Fan blades and motor were acceptable Condenser coils were acceptable Cleared debris from the bottom of the unit Washed condenser coils from the inside out Waxed the top of the unit Recommendation today is to upgrade from compressor saver to the micro Air soft start kit Installed Micro Air Soft start kit

Just recently had smoke detectors replaced and customer has a crouse hinds panel and it looked really good no burning or broken or rusted over screws or doubled nuetrals only had 1 ground going to cold water but talked to customer about adding a ground rod and also adding surge protection to protect computers and all electronics in house but customer did not like the price but informed him that I would email it to him so that he could think about it and if you didn't want to do in the future he could just go thru the email

2018 Amana Gas Furnace Checked and tightened all electrical connections Filter was acceptable recommended buying extra in case needs to replaced in summer Drain has slight build up in trap UV system is functional, UV lamp is burned out Blower Motor and wheel were acceptable Evaporator coil was acceptable 2018 Amana Straight Cool Checked and tightened all electrical connections Dual run cap was within manufacture range Primary electrical unit was acceptable Refrigerant levels were showing off due to 35° ambient temp Fan blades and motor were acceptable Condenser coils were acceptable Cleared debris from the bottom of the unit Washed condenser coils from the inside out Waxed the top of the unit Recommended UV lamp replacement, pan treatment, clear drain or upgrading UV system to more efficient system

Came to house to quote running power out to shed and adding a midi split and also adding a RV plug and 100 amp panel and adding a bunch of plugs and lights and everything inside of it so gave quote and emailed it to him and customer says that he is getting a few more quotes before he decides and will reach back out to us whenever he does

3/7/2026 Location of package unit is in the backyard near the back porch area to access all the electrical components is under porch which is nothing but mud going to reschedule for next Saturday 3/14/26 first call first call when under the porch is dry and there's no rain

Upon arrival customer stated that the system would not cool the home found that the air handler was blowing but the heat pump was not running during evaluation found the dual run cap to be failed replaced door run cap reset system and system began to cool talk with customer micro airsoft start kit customer agreed to install soft start kit left with system and cool

.

Super tune up performed today on an Amana heat pump with air handler installed in 2018. All electrical connections are tight with no corrosion. X13 blower motor is acceptable. Blower wheel and evaporator coil are clean. UV bulb needs to be replaced. Compressor and condenser fan motor are acceptable. Refrigerant levels are in range. Outdoor unit was washed and waxed.

2025 Ducane Airhandler Checked and tightened all electrical connections Customer did not have an extra filter today Drain was clear and draining at this time Blower motor and wheel were acceptable Evaporator coil was acceptable 2025 Ducane Heatpump Checked and tightened all electrical connections Dual run capacitor was within manufacture range Primary electrical unit was acceptable Defrost board was acceptable Refrigerant levels were acceptable at this time Fan blades and motor were acceptable Condenser coils were acceptable Cleared debris from the bottom of the unit Washed condenser coils from the inside out Waxed the top of the unit Recommended UV system to keep system and air clean, whole house surge protection, compressor saver, Star warranty upgrade and HBPPLAN

Upon arrival customer stated the system would not keep up during the Cold snap. During evaluation found that the compressor was running but the fan motor was not also found that the fan motor nuts had come loose and the fan dropped causing blades to hit condenser casing and completely stopped the fan motor from running. In turn causing the fan motor to become extremely hot. Remounted fan motor and fan motor came on but unsure of how long the fan motor has been that way and how long the compressor has been running without the fan motor talked with customer about fan motor replacement and other recommendations as refrigerant levels are showing low technician performed League search on the evaporator coil could not find a leak but the evaporator coil the blower and the duct system need to be cleaned which could potentially be causing poor air flow in turn reflecting on refrigerant levels. Talk with customer about cleaning the system adding surge protection and a compressor server along wi

Super tune up performed today on a five year old Amana two stage heat pump. All electrical connections are tight with no corrosion. Evaporator coil has some build up starting to form and should be cleaned to help with the airflow across the coil. Heat strips are pulling proper amperage. Compressor and condenser fan motor are acceptable. Reversing valve and defrost control board are working properly. Refrigerant levels are in range. Outdoor unit was washed and waxed.

Replaced condenser fan motor. Found burnt wires at primary electrical control for heat strips. Got customer up and running for now. Will need to come back out in 2 weeks per Mark W to double check voltage issues and heatkit pausing for now

Heating tune up 2017 straight electric Coleman Airhandler Checked and tightened all electrical connections Changed customer provided filter Drain was clear and draining at this time Heat strips were functional and within Manufactured range Blower motor was acceptable Blower wheel has dust dirt and biological growth build up Evaporator coil has dust dirt and biological growth build up Recommended level 2 duct cleaning and UV system for biological growth and clean air

Came out to job to do electrical inspection and everything looked good Nathaniel was the last one that was out here and did a bunch of work he has also changed a few plugs and everything already but also customer wanted to see about making a plug in his garage on its own circuit and also running a coax through his attic and down into another room behind a TV and gave him a quote to do both but what was a little too high for him but talk to him about it and emailed it to him and he will reach back out to us when he is ready

Customer states furnace was not running this morning. Furnace was running apon technician arrival. Technician cleaned flame sensor and checked all saftys. Everything is working accordingly. Customer stated back bedroom is 5 degrees warmer than the rest of the house in the winter time and colder during the summer due to imbalance airflow. Technician found that duct to far bedroom is on the very end of supply plenum causing more air to flow than the other ducts. Suggest rebuilding supply plenum and moving back bedroom duct. Furnace is running and heating the home upon departure.

Super tune up performed on a Trane heat pump with air handler installed in 2020. All electrical connections are tight with no corrosion. Heat strips are pulling proper amperage. Blower wheel rl and evaporator coil are clean. Drains are clear. Compressor and condenser fan motor are acceptable. Refrigerant levels are in range. Outdoor unit was washed and waxed. Suggest adding an IAQ 300 Germicidal system to help with the air quality within the home.

12/29/25 Installed drain switch on the downstairs unit and replaced 7.5 blower capacitors on both the upstairs and downstairs units. Inducer motor that was ordered was the wrong part. Need inducer motor for Carrier Model: 58STA090-16 Serial : 1407A30432 Carrier part # HC21ZE122A Will collect remaining balance upon completion of the work.

They are not interested due to price

Softener Job is complete and working like it should

Will return tomorrow and install new salt softener 12-23-25

Came to house for electrical tune up and talk to customer about surge protection and also about how his panel is old and also looked at a few other things but customer did not want to do anything at the moment but did want an email about the search protector so emailed him that

Cut linest to fit, install line set, pull vacuum and set charge. Including line set cover. Job is set for Tuesday morning first call. Need to order a mini split line set cover. Requesting Nate M to help with install and start up.

Got jacket that was left behind

3 system super tune up perfomed today. All systems are gas furnaces with straight cool condensers. 7.5 mfd blower capacitors in the main unit and the upstairs unit are out of spec and need to be replaced. Inducer motor for the main downstairs unit is amping high and making a grinding noise. Inducer needs to be replaced. No drain protection on the main downstairs system. Bedroom furnace is only two years old. All electrical connections on all three units are acceptable. Refrigerant levels are in range. All safeties are working properly. All systems running as they should at this time.