HVAC, Plumbing, & Electrical Services in Richland Hills, TX

8/13/25 Arrived waited for 20 min tried to contact customer no answer or return call moving on at this point no show on job

for this job, I did an evaluation. On arrival indoor system was running but condenser was not. L6 error code on board. Capacitor at 18 MFD rated for 35mfd. Swapped capacitor and system turned on. had a good Delta and was running when I left.

On this job I found an 04 open start circuit. I replaced hard start under warranty. System is back online and ready for cooling.

Completed cooling tune up All electrical components good amp draws good Freon levels good changed filter cleaned condenser drains clean and clear collected payment by credit card

Came to house and nobody was here or answering the door and I didn't realize that it was still pending So I am pausing the job and when we hear back I will come out Hang back to job when customer was ready. And customers having a shocking issue with cooktop. Cooked up when microwave is plugged in next to it, talk to them about running a new circuit. So it can be grounded. Customer was very pleased.With us and how we work

For this super tune-up I inspected the customer's air handler and condenser testing the equipment in both heating and cooling. Overall equipment looked within manufacturer specs and was running well. I would highly recommend to the customer that we replace the existing hard start kit as it is dead and no longer functioning in the capacity it is supposed to. The compressor is overamping on startup pulling higher amps than what it is rated for which in the long run can cause more damage and cause that compressor to fail. A compressor saver kit will lower that amp draw and keep it within range increasing the longevity and efficiency of the compressor. I also recommend that we install a whole home search protector into the electrical panel to protect all the vital electronics within the home from power surges and lightning strikes and damage the those can cause. The customer had to leave while I was working on the outdoor unit so I was unable to make these recommendations at the time.

On arrival system running and cooling producing 19 degrees delta. Indoor unit clean but uv bulb is 5yo and should be replaced. Recommended upgrading to iaq 200. Outdoor unit passed all electrical testing. System cooling as I left.

Performed plumbing tune up customer had foundation work and needs cleanouts for testing. Gave estimates for c/o and tankless service valves. Customer will call back

For the super tune-up I inspected the customers furnace and condenser, system was functioning and running well and both heating and cooling and customer is set for summer.

Being that the gas line is out of service I couldn't look a functionality of the heater. He wants to talk to some one this Monday 10 am about getting a new electric air handler and relocating it to the garage. The cooling side of the system has a 8° subcool and td is 20°.

On this job I changed out a flame sensor under warrenty.

Plumbing – Eval- Sewer Issue

Arrived onsite customer had a main line stoppage on home. Went ahead and ran sewer machine through drain and cleared stoppage for home. No warranty on sewer cleaning customer has old clay pipe in yard he knows he needs to replace.

System was heating intermittently when it wasn’t heating in the sequence of events in the furnace operations. Gas came on and then system shut off, so I determined it was the flame sensor. I changed it out system now heating.

Arrived at customer house for rec work Installed new control board unit is working both heating and cooling after new board was installed

Arrived at customers house for evaluation Consistent power both high and low to board board pulsating power To all components Order new board to install P and L

He has a heat 10 year old heat pump with a new evap coil. The system Has a 20kw back up heat strip. Each strip pulls different amps 17 18 20 22.2. His heat pump currently works and has a subcool in cooling of 9°.

Arrived for heating tune up All heating components are in tolerance System delta 19 Replaced filter Capacitor and compressor saver are good Reccomended IAQ200 System left on cool at exit

Arrived fit service Eval Hard start kit failed Replaced and system running fine at exit

Arrived fit service Eval Locked rotor code Capacitor and hard start kit fine Tightened all high voltage connection and all measurements in tolerance at low and high stage Cleaned Condenser coil as well since high pressure lockout was the most recent other error code