5/16/24 On arrival system was off. Customer stated evaporator coil was freezing and leaking water. Drain line flowed when flushed, filter was changed before I arrived after coil had frozen.i informed customer that due to the rain I would be unable to fully confirm why the coil froze. Airflow appeared good but any refridgerant check I do in the rain is not accurate. Pausing call to reschedule.

Tech arrived at a tune-up. Upon inspection, the capacitor was within specs. The new outdoor unit was pulling high amperage on start-up. The condenser coils were hosed off to assist with air flow across the coils. The filter was dirty and replaced. The drain was clear and bleach was poured. The Delta and refrigerant was within range. The refrigerant was high. The customer was informed of recommendations today. She decided to move forward with adding a Compressor Saver to release stress on the compressor. This item was installed, tested and functioning. The system was functioning upon departure.

On arrival system was running and not cooling. The system had a 4-5 degree subcool and is designed for a 10 subcool indicating low refridgerant. The low side saturation temp was 30 showing that the evaporator coil was below freezing. The drain lines were run improperly and there were no water safety's. The evaporator coil was extremely rusted. The outdoor units contactor and capicator were in rough shape and needing to be replaced. The system holds 6.4 pounds of refridgerant so I quoted 56 oz. I also quoted an evaporator coil due to the extreme rust and absence of leaks on the outdoor unit. I recommended speaking to a comfort advisor about replacement due to the cost of repairs, the condition of the system and the 2 week wait on carrier coils vs the quick turnaround time on replacement. Rob is going to call tomorrow to give an estimate.

Tested all components all measured within ratings and specs. Refrigerant level is normal. Washed and cleaned condenser. Changed filter. Recommend duct cleaning lvl1. Emailed estimates.

Tested all components all measured within ratings and specs. Refrigerant level is normal. Washed and cleaned condenser. Customer did not have replacement filter. I recommend getting the ducts cleaned and replacing or upgrading uv light. Recommended upgrading filter to aprilaire. They want to talk about it and get back to us. Estimates emailed.

Tested all components all measured within ratings and specs. Refrigerant level is normal. Washed and cleaned condenser. Changed filter. Recommend duct cleaning lvl1

Tested all components all measured within ratings and specs. Refrigerant level is normal. Washed and cleaned condenser. Changed filter. Recommend duct cleaning lvl1

We figure the noise is a mix between the intial rush of refrigerant and the blower motor kicking on. This system is new and all conpenets are in tolerance. The system hasn't been operational is sometime this can be a cause for concern when your unfamiliar with it's habits and intial start up. The system could benifit from a hard start kit as well.

This system has alternating voltage coming from the broad outside. Leads me to believe that the broad out side needs to be replaced. This is a Mr cool mini split system. He wants to check with Mr cool about warrenty.

On arrival system was running and cooling producing a 20 degree delta. Indoor unit was mostly clean, the coil was dusty and there were early signs of biogrowth in the supply plenum. The outdoor unit passed all electrical inspection but was overamping on start up.

Customer stated that upstairs unit temperatures were higher than downstairs temperatures. Found that zone damper for upstairs unit was receiving the proper twenty four volts to close damper, But damper motor had shorted not allowing damper to close. Recommended replacing damper motor for upstairs. Found no other issues at this time.

This system will not be replaced untill system brakes down completly. With that the system could beinfit from a total break down cleaning a UV system and hard start kit.

Arrived for AHC Current UV system inoperable and has growth on the fuel cell and in the supply plenum Recommend upgrading to one of our lifetime warranty UV airflow cleaners Blower and coil are dusty with biological growth Outdoor coil relatively clean Filter upgrade recommended to keep unit clean for longer Customer will discuss options with his wife and get back to us

Arrived for rec work Lifted and supported furnace Reattached file pipe Replaced flame sensor on main unit System left in heating at exit

Arrived for STUx2 Replaced filters Drains clear Condensers clean Capacitors and motors are fine Will return Friday 3/8 to lift and remount bedroom furnace, install IAQ200 and replace the flame sensor in the main house unit

On arrival system was running and cooling producing a 20 degree delta. The indoor unit had clear drain lines and a clean blower but the underside of the coil was dirty due to air bypassing the filter. The outdoor unit passed all electrical testing. I recommended an April aire media upgrade kit to improve filtration and replacing the uv bulb or upgrading to an air scrubber to improve air quality and prevent further biological growth. When I left the system was on and cooling.

Customer stated that indoor unit was making a loud noise. Ran indoor through three diffrent cycles, and was unable to replicate noise. Found no issues with unit at this time.

Tech arrived for rec work. The Zone board was installed, tested and functional in both modes.

Tech arrived at a warranty tuneup. Upon inspection the capacitor was within specs. The contactor was in working condition. There was no observed surge protection. The condenser coils were hosed off to assist with air flow across the coils. The Delta was within range. The filter and blower area was clrean. The drain was clear and bleach was poured. The customer was informed of recommendations today. He will wait until his first payment to update membership. He is interested in UV system but will review the quote with his wife. The system was functioning upon departure.

Mike R. completed annual heat and air conditioning system tune up.

On this tune up I discovered the basic blower motor cap out of tolerance. I also moved the blower motor to a slower speed for heating. He has a new EVAP coil replaced under warrenty. The condensor also had a bad contactor. After everything they system is updated cleaned and ready for heating

Tech arrived at a no heat. Upon inspection the board was getting low voltage call into the Zone board but it was not leaving the board. The various other components were checked. The transformer was replaced. The Zone board appears to be faulty. The customer was informed of recommendations today. He decided to have the Zone board ordered for replacement. The board was bypassed so that the customer has heat in the meantime. Honeywell Zone Control board HZ221 TrueZONE Braeburn 3 zone 140303 We will pause for parts and to collect payment