Licensed Electrician in Weatherford - Same Day

We inspected and serviced a 2019 Amana Airhandler, ensuring all electrical connections were secure and tight. We replaced the filter using the customer-provided one. The primary P-trap showed buildup, while the blower motor and wheel were in good condition. However, the blower wires exhibited biological growth buildup, and the evaporator coil had slight biological growth. For the 2019 Amana Heatpump, we checked and tightened all electrical connections, confirmed the dual run capacitor was within the manufacturer's range, and ensured the primary electrical unit was acceptable. The defrost board, refrigerant levels, fan blades, motor, and condenser coils were all acceptable. We cleared debris and washed the condenser coils, then waxed the top of the unit. We recommended upgrades to CCC, UV 200, and clearing the drain. The customer wishes to discuss these recommendations with family.

We began by identifying and replacing the faulty pipe and fittings at the water heater, which were part of the original installation from 08/25. The copper tubing had developed a pinhole leak at the top near the circulation pump. Given that there was no warranty on the existing copper pipe, fittings, or pump, we proceeded with the replacement. We carefully removed the old, leaking copper tubing and installed new, high-quality copper piping to ensure a secure and leak-free connection. The circulation pump was also inspected but remained in service as it was not covered under warranty. The job was completed efficiently, ensuring the water heater operates safely and effectively.

I successfully installed a customer-supplied UV system and transformer, ensuring all components were securely and correctly positioned. Following installation, I conducted a thorough function check to verify the system's performance. The UV system is now effectively sanitizing the air, while the air conditioning unit operates smoothly, providing optimal cooling. Both systems are fully operational and functioning as intended, ensuring the highest level of efficiency and satisfaction.

I successfully completed a water heater element replacement for a customer. The task involved removing the old, faulty upper heating element and installing a new one supplied by the customer. Despite the absence of a warranty on the new element, I ensured the installation was done meticulously to guarantee optimal performance. The service fee covered the labor and any necessary tools for the replacement. Throughout the process, I maintained clear communication with the customer, explaining each step and ensuring their satisfaction with the work performed. The new element was installed correctly, and the water heater is now functioning efficiently.

Upon arrival, the system was not cooling. Upon inspection, both the primary and secondary drains were found to be blocked, causing the emergency drain pan to overflow and activate the drain switch. I promptly cleared the blockages from both drains and emptied the emergency drain pan. To prevent future issues, I installed a condensate drain pan treatment. After completing these tasks, the system was operational and cooling effectively by the time I left.

I recently assisted a customer in evaluating various home service brands for his rental property. We reviewed options for appliances, maintenance services, and utility management. I provided detailed insights into each brand's offerings, reliability, and customer service. The customer appreciated the comprehensive analysis and plans to make a decision within the next two days. This consultation ensured he has all necessary information to choose the best services for his rental.

Upon arrival, the system was not cooling. A failed 35/5 capacitor and a malfunctioning compressor saver were identified as the issues preventing the compressor from starting. Both parts were replaced under warranty, with the parts covered by membership and labor extended by Brian H. After the replacements, the system was tested and successfully began cooling, ensuring the home's comfort upon my departure.

Upon inspection, the 2018 water heater required a thorough flush to ensure optimal performance and longevity. The plumbing system throughout the property was evaluated and found to be functioning correctly. To further assess the condition of the drain lines, a camera inspection was conducted, revealing no visible leaks or blockages. The customer is considering upgrading their maintenance plan and will discuss this possibility further. The service provided included a comprehensive evaluation of the water heater and plumbing system, along with a detailed inspection of the drain lines using advanced camera technology.

I performed a $99 drain cleaning service. First, I ran a cable through the laundry sink drain to clear any blockages. During this process, I encountered some roots obstructing the line. I successfully pulled back a portion of these roots using the cable. While the drain is now clear, I want to emphasize that there is no warranty on future stoppages. To prevent future issues, I recommend running a camera through the line to locate and address any root intrusion. This proactive step can help avoid recurring problems.

Upon arrival, I identified an issue where the unit was turning on and off intermittently. After thorough inspection, I discovered a partial blockage in the drain switch, causing it to trip and shut off the system. I carefully cleared the blockage from the primary system's drain. To prevent future issues, I installed a drain pan treatment in both systems. Following the installation, I conducted a function check and confirmed that both systems were operating normally before leaving the site.

Upon receiving the request for attic insulation estimates, I conducted a thorough assessment of the space. I evaluated the existing insulation and identified areas that required improvement. After analyzing the customer's needs and budget, I provided three distinct levels of insulation solutions. The first option focused on basic insulation, while the second offered enhanced thermal performance. The third level provided superior insulation, ensuring maximum energy efficiency. I explained the benefits and drawbacks of each option, enabling the customer to make an informed decision. The chosen solution was then implemented, resulting in a more comfortable living environment.

Upon inspection, the downstairs unit displayed four locked rotor codes, indicating a significant issue. Upon further investigation, it was determined that the compressor saver had failed. This component is crucial for protecting the compressor from damage due to overcurrent. After confirming the diagnosis, I replaced the 3-ton compressor saver. The system was then thoroughly tested to ensure proper functionality. The callback was successfully completed, and the unit is now operating efficiently. This resolution prevented potential compressor damage and restored the system's reliability.

Upon arrival, I assessed the customer's complaint about the cooling unit stopping. The blower was operational, but the outdoor unit was inactive. I reset the thermostat to cooling mode, and the system restarted successfully. I checked refrigerant levels, which were normal, and ensured the drains were clear. The air filter was slightly dirty, so I cleaned it. I also inspected the TXV and the Coleman inverter unit, finding no visible codes. The system is now running and cooling effectively.

Upon arrival, the Amana gas furnace with a straight cool condenser, installed in 2019, was not providing any cooling. The condensing unit displayed an L6 code, indicating a failed capacitor. I replaced the 35mfd capacitor under warranty, ensuring the system's reliability. Additionally, I installed a compressor saver to enhance the efficiency of the compressor during startup. After completing the installation, I conducted a thorough function check to verify the system's performance. The system was successfully running and effectively cooling the home by the time I departed.

Upon arrival, I identified that the second tank was experiencing a blockage at the inlet, preventing proper water flow. To address this issue, I carefully removed the pipe where the water enters the tank. This action successfully restored the flow, allowing the tank to function correctly again. Additionally, I plan to investigate the possibility of sourcing a new controller for the pump to prevent future issues. To ensure the customer is fully informed, I will reach out on Monday or Tuesday to discuss the situation and any potential next steps. This thorough approach aims to provide a lasting solution and maintain the system's efficiency.

Upon arrival, I conducted a thorough inspection of the system as requested. I checked all components for functionality and identified potential issues. I took detailed notes and documented my findings. I attempted to contact the customer via phone but did not receive an answer. Given the circumstances, I decided not to leave a voicemail and instead planned to gather more information. I will follow up with the customer on Monday to discuss the findings and next steps. I ensured all equipment was left in a secure and orderly condition before departing.

Hshdhdj

Upon arrival, I conducted a thorough inspection and discovered unusual refrigerant levels, indicated by a very low delta temperature. The coil was not circulating refrigerant properly, causing it to warm up. To prevent further damage to the compressor, I advised the customer to shut off the outdoor unit immediately. I scheduled a Comfort Advisor visit for 9 am on 10/9/26 to address the issue comprehensively and ensure the system operates efficiently.

Upon arrival, I identified that the disconnect switch was left in the off position, which was affecting the system's functionality. I carefully examined the switch and confirmed its position. To resolve the issue, I turned the disconnect switch to the correct on position. After ensuring the switch was properly set, I tested the system to verify that it was operating as intended. The system responded correctly, indicating that the issue had been successfully resolved.

On 10/7/26, I performed a comprehensive tune-up. I inspected the electrical connections, which were secure, and found the coil acceptable. The blower wheel showed minor biological growth. I recommended a UV system, which the customer decided to purchase. I also checked the outdoor unit, ensuring all electrical connections were tight and the capacitor was within range. The top of the unit was cleaned and waxed. Refrigerant levels, compressor, fan motor, and heat strips were all functioning correctly. The customer plans to use her free service fee for the UV light installation.

I thoroughly inspected and maintained the 2025 Ducane Airhandler, ensuring all electrical connections were secure and tight. I replaced the filter with the customer-provided one and confirmed the drain was clear and functioning properly. The blower motor and wheel were inspected and found to be in acceptable condition. The evaporator coil was also checked and deemed acceptable. For the 2025 Ducane Heatpump, I verified all electrical connections were secure and tightened as needed. The dual run capacitor was within the manufacturer's specified range. The primary electrical unit, defrost board, and refrigerant levels were all acceptable. The fan blades and motor were inspected and found to be in good condition, as were the condenser coils. I cleared debris from the bottom of the unit and cleaned the condenser coils from the inside out. I recommended installing a Micro Air Soft Start or Compressor Saver to reduce inrush amp draw and a UV 200 to prevent biological growth and maintain clean

Upon arrival, the customer reported a blank thermostat and suspected a blown fuse. After thorough evaluation, I confirmed that the fuse was intact. Further inspection revealed that the primary drain line was clogged, causing the float switch to trip. The customer mentioned that a previous technician had not identified this issue during their visit. I cleared the clogged drain and utilized the recall function to address the missed issue. The system was left operational in cooling mode.

During the tune-up, I inspected a 2007 Carrier air handler and heat pump. The evaporator coil was heavily rusted, and the blower motor and wheel were compromised. The drain was filled with debris and lacked protection. The TXV bulb was found outside the unit, likely not functioning properly. The return air was inadequate, and the primary electrical unit had significant carbon buildup. The refrigerant levels were acceptable, but multiple components showed severe rust. I recommended replacing the system due to its compromised state and high repair costs. Photos and detailed recommendations were sent to the customer.

I contacted the customer to schedule an appointment for a comfort advisor, focusing on adding a second unit to the primary bedroom and splitting the home into two systems. Upon arrival, the system was not cooling. I identified a low pressure switch trip code on the outdoor unit, performed a hard reset, and allowed the system to restart. After ensuring refrigerant levels were within range, I confirmed the drains were clear and airflow was adequate. The air filter was slightly dirty, so I replaced it to rule out any potential issues. The system resumed normal operation, effectively cooling the home by the time I left.

On September 28, I received a request from a customer for estimates on the rough-in and top-out phases of their project. I reviewed the provided plans and scheduled a meeting with the homeowner and Mark W for October 5. During our discussion, we thoroughly examined the plans, ensuring all requirements were understood. I will contact the homeowner shortly to provide a detailed estimate, aiming to start the project promptly and efficiently.