Fast, Reliable Plumbers in Fort Worth - Same Day

I thoroughly inspected and serviced the entire electrical system, ensuring all components were functioning optimally. The amperage draws were verified to be within acceptable limits, and the refrigerant levels were confirmed to be at the correct levels. The temperature split was measured and found to be within the ideal range. Drains were meticulously cleaned to ensure they were clear and unobstructed. The condenser was cleaned to remove any debris, and the filter was replaced to maintain efficiency. All gas safety mechanisms were checked and found to be operational. The equipment was tested and confirmed to be working properly, ensuring a safe and efficient system.

I successfully diagnosed and repaired the wiring unit, ensuring it functioned correctly. I meticulously checked each connection and tested the unit to confirm its proper operation. After completing the repair, I provided a detailed explanation of the work performed to the client. Payment was collected via credit card, and I ensured the transaction was processed smoothly. The client expressed satisfaction with the service provided.

Upon arrival, I assessed the thermostat and confirmed it was malfunctioning. I promptly replaced the faulty thermostat with a reliable, basic model. Ensuring the new thermostat was correctly installed, I calibrated it to maintain optimal temperature settings. Throughout the process, I explained the functionality of the new thermostat to the client. After completing the installation, I processed the payment via credit card. The client was satisfied with the efficient and professional service provided.

I began the super tune-up by thoroughly inspecting the outdoor unit and checking refrigerant pressures. The outdoor unit was cleaned, revealing higher-than-recommended amperage draw. I recommended a soft start to improve performance and extend compressor life, though the customer opted to consider it. I also discussed a compressor saver as an alternative. Inside, I verified a proper 17–18°F temperature split in cooling and a 140°F supply temperature in heating. I flushed 2 gallons of water through the drain line and inspected internal components. Dirty return ducts and biological growth between the evaporator coil and blower motor were noted, with recommendations for professional duct cleaning and a germicidal light system. Estimates were provided and sent via email.

I began the heat pump heating tune-up by thoroughly inspecting the outdoor system. Refrigerant pressures were within the acceptable range, and I cleaned the outdoor unit to ensure optimal performance. All components were verified to be functioning correctly. To protect the outdoor control board, I recommended and installed a surge protector, which the customer approved. For the indoor system, I coordinated a duct cleaning service for the next morning. Additionally, I noticed an existing UV light and recommended an RM2 oxidation system for improved indoor air quality, which the customer also approved. After installation, I verified proper operation, replaced the air filter, inspected the drain system, and flushed the primary drain line with four gallons of water. The system was operating correctly, producing approximately 170°F air with a 21°F temperature split.

During the service, I performed a thorough inspection and tune-up of the air handler. I discovered significant dust and biological growth inside the unit, which was causing a noticeable loss of cooling capacity. The accumulation of dirt and dust had reduced airflow, increased condensation levels, and extended system run times. I meticulously cleaned as much of the dust and dirt as I could reach, but a deep cleaning is necessary for optimal performance. I explained the situation to the customer, and they plan to discuss the deep cleaning with their spouse. Once they decide to proceed, we will schedule the additional service to restore the system to full functionality. Thank you for choosing our services.

I performed a Super Tune-Up on the heat pump system. Starting with the outdoor unit, I checked refrigerant pressures, which were slightly off the recommended range. After discussing with the customer, I adjusted the refrigerant. The outdoor fan motor was drawing excessive amperage, likely causing intermittent cycling issues during hot temperatures. I recommended replacing it and provided an estimate. I cleaned the outdoor unit before moving inside. The indoor unit showed a 21°F temperature split, indicating proper cooling. The condensate drains were flushing correctly, and the air filter was clean. The blower motor fins were dirty, but the customer declined cleaning. I recommended a duct clean and left an estimate. All other components were functioning well, and the UV bulb was operating properly. The system was cooling as intended upon departure.

I conducted a thorough evaluation of the system and successfully cleared the drain line. To enhance the system's efficiency, I installed an RM one germicidal light in the downstairs unit and an RM to oxidation germicidal lamp in the upstairs unit. These additions will help maintain cleanliness and reduce the risk of bacterial growth. Additionally, I advised the customer to pour bleach down the drain every six months to ensure optimal performance. For the initial bleach treatment, I recommended doing it every two hours, six to eight times on the same day. After completing the installation and maintenance, I tested the system to confirm that everything was functioning correctly. Thank you for choosing our services.

Today, I successfully completed a residential electrical work unit. I began by thoroughly inspecting the existing wiring and outlets to ensure everything was in proper working order. After identifying the necessary repairs, I replaced faulty outlets and corrected any wiring issues. I also tested the circuits to confirm that all electrical components were functioning correctly. Throughout the process, I maintained a clean and safe work environment. Upon completion, I provided a detailed explanation of the work performed to the customer and collected payment via credit card. The customer expressed satisfaction with the quality of work and professionalism demonstrated.

I performed a comprehensive super tune-up on the gas furnace system. Starting with the outdoor unit, I checked refrigerant pressures, inspected internal components, and cleaned the unit. I recommended a soft start, though the customer declined. Inside, I verified the air filter was in good condition and checked the temperature split, which was 21°. I flushed the condensate drain line and inspected all internal components. I suggested professional duct cleaning and provided an estimate. The UV air purification system was non-functional, so I recommended upgrading to the IAQ200 or IAQ300 system. I also presented the membership program benefits, but the customer declined. Estimates for all services were provided. The system was operating correctly upon departure.