Heating and Cooling Services in Mansfield TX

For this eval I showed up to the customer's home and was informed the unit has not been working since january. Upon going into the attic I noticed this house is operated via a zone system and the fuse was popped. I replaced the fuse and jumped R&Y. After doing this the system ran for approximately 30 seconds and then popped the fuse again. Upon this happening I went to the condenser and the condenser was not running, I tested voltage and was getting 240 on the lower legs, but no voltage on the top or bottom because the contactor was not engaged, signifying there was no call from the thermostat. I checked the thermostats again and they were both in cooling and set to 68°, I went back to the Attic and tested the transformer and was getting 120 volts but no 24 volt call. I changed out the transformer and the system ran for another 30 seconds and popped another fuse. I tested voltage again on the bus bar at C&Y and R&Y with no voltage reading. I went back to the condenser and swapped out

For this super tune-up I inspected both units furnace and condensers. All equipment was measuring up with a manufacturer specs and running well. With the customers having 4 in box filters, I do recommend the AprilAire upgrade kit, for better dust capture unless wear on equipment overtime. Additionally both UV lamps were out therefore I recommend replacing those bulbs if they feel like they're beneficial to them, as well as installing compressor savers on both condensers to lower the amperage on startup. Lastly I do recommend home surge protection as they have both units and this will protect any damage during lightning strikes or major power surges.

Found leak on liquid line Corrected and adjusted refrigerant

During inspection discovered that tstat needed to be programmed after losing power and tested all components after and system was working properly Customer stated that she had a hallway light fixture that had gone out and I let her know I would setup an appt for a electrician to come out and take a look at it Set appt for electrician to return 4/24/24 first thing in the morning

During inspection verified that systems were working properly Spoke to customer about upgrading his uv systems to a better system so that they do more and the bulbs last longer and also recommend pan strips to prevent drain line problems Customer stated he would hold off for now but look towards getting some of it done in his fall tune up Left customers house with systems operating properly

For this super tune-up I inspected the air handler and condenser. All equipment was measuring within manufacturer specs and running well. I converted the customer to the home and budget protection plan membership informed her of her benefits.

Arrived for two system STU All components were working andnin tolerance Recommend IAQ 200, 1000, Blower clean, evap clean, Compressor saver, drain switch and membership. Relayed Information to customer. Customer with talk to husband.

Arrived for inspection 2003 furnace system low on refrigerant - R22 Furnace nonfunctional - declined eval as he is ready to replace anyways Comfort Advisor scheduled for 4/1 10 am for system and insulation

This system is new and in tolerance. The condensor coil is clean and ready for cooling. The filter is also fresh. This system could benifit from a UV system and hard start kit.

AC & HEAT TUNEUP ON 2 UNITS

During inspection verified that system was working properly Spoke to customer about recommendations for the system and those included a compressor saver and pan strip and customer stated he wanted to hold off on those purchases for now Left customers house with system operating properly

Tech arrived at a 2 system tuneup. Upon inspection, the bedroom system was aged and dirty. This system was not functioning in cooling mode. There was air leakage that was repaired. The capacitors were within specs. The main system was also dirty. The drain line was clogged. The customer was informed of recommendations today. They decided to unclog the main system primary line and add a treatment strip to help keep the drain system clean. These actions were performed and tested. The customer will call back in to upgrade the filter and have the system cleaned. The bedroom system was not functioning upon departure.

Install 36k heat pump mini split

Annual heat and air conditioning tune up.

For this cooling tune up I inspected the airhandler and condenser. All equipment was within manufacturers specs. I recommend a level 1 duct cleaning, a UV system, and surge protection. Customer will call if interested at a later time.

During inspection verified that systems were working properly Spoke to customer about recommendations for the system and also a duct cleaning for his upstairs system due to the amount of build up inside the ducts The customer just wanted to go ahead and get the compressor savers installed onto the systems today and have us back out the next time to install the uv systems and do a duct cleaning

Tech Cody Brooks arrive to customer's home. I met Mrs Elliott and she directed me inside to the thermostat and attic access. I started indoors with replacing the filters, and open up the cabinet to do my visual inspection. The coil and blower both looked clean, as well as the drain pan. I then turned the unit on to heat and the furnace went through all safeties without issue and the inducer motor was pulling amperage within tolerance according to manufacturer. I then headed outside and started with washing down the coil, there was lots of dirt and dust buildup but I got it all out and removed all the dirt and leaves from the bottom of the unit. The compressor and fan motor both had runnimg amps below manufacturer specifications. The unit did not have a hard start kit Installed and this was reflected with a high in Rush amp test. I then attempted to get the coils to dry but it has been raining the entire job and so I was not able to get accurate refrigerant readings. I informed the cust

During inspection verified that systems were working properly Spoke with customer about recommendations for the system including Drain switches, compressor savers,pan strips and a whole home surge protector Customer stated she would most likely have us back out to install the pan strips

3/21/24 Reschedule due to weather. Customer said 10-5 window is the preference for tomorrow.

Arrived for eval where the system wasn't heating and blowing out cold air and the blower motor wouldn't turn off. Found high cut out to be broken and not allowing out side system to turn on Temporary jumped high pressure switch and system ran as normal Relayed Information to customer Customer only wanted high pressure switch to be bypass at this time

I found that the pool pump was a mess of wires so I remade the connections and the GFCI then worked

System is working and in tolerance on the new system. I changed both filters and washed condensor. The older system is failing from time to time due to temp sensor failing. No telling how long that will work for.